Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Honeywell Vent Sanitizing: The Orlando Owner’s Guide
We stock and install Honeywell-compatible vent sanitizing systems across Orlando, with most replacements running between $385 and $720 installed depending on your duct configuration and which Honeywell UV or sanitizing unit your home uses. Most Orlando homeowners call us after noticing the sanitizing lamp has stopped glowing through the access window, or when a family member’s allergies tick back up even though the filter was just changed. The fix is usually straightforward, and we carry the common Honeywell replacement lamps and ballasts on our trucks so we can often resolve it in one visit.
Here’s the scene we see all the time in neighborhoods like College Park and Baldwin Park: a homeowner opens the air handler closet, glances at the Honeywell unit, and realizes the little blue or purple light that used to glow inside the duct has gone dark. That’s the most common entry point to this conversation. Sometimes it’s the lamp itself that has burned out after a few years of Florida runtime. Sometimes it’s the ballast or the power supply. Either way, you don’t need to guess, and you don’t need to climb into a hot attic in July to figure it out. We tell you what we found, what we will do, and what it costs, before we start.
Key Takeaways:
- Honeywell vent sanitizing replacement in Orlando typically runs $385 to $720 installed
- Most failures are the UV lamp or the ballast, both of which we stock
- We’re an independent Orlando service provider, not affiliated with Honeywell
- Written price before any work starts, every time
Which Honeywell Models This Applies To
We work on the Honeywell UV air treatment systems most commonly installed in Orlando homes: the UV100A, the UV2400, and the older UV500 series. Each uses a different lamp length and wattage, and that’s where a lot of DIY orders go sideways. The UV100A takes a shorter lamp, typically around 14 inches, while the UV2400 lamps run closer to 17 inches and operate at a higher output. If you buy the wrong length, the lamp physically won’t seat in the bracket, and you’re out the cost of the part plus return shipping. We’ve had more than one Orlando homeowner hand us a box from an online order that was never going to fit their housing.
The easiest way to identify which lamp you need is to look at the silver label on the side of the UV housing. Honeywell prints the model number there, and the lamp wattage is usually stamped on the lamp’s ceramic end cap. If the label has faded from Florida humidity, we can match it by measuring the old lamp and checking the pin configuration. On the OEM-versus-aftermarket question: genuine Honeywell lamps carry a one-year manufacturer warranty and are what we install by default. There are quality aftermarket equivalents available, and we’ll quote both if you want to compare, but for a part that runs continuously in a hot, humid duct, we lean OEM. The cost difference in Orlando is usually small enough that the warranty makes the decision easy.
Styles & brands we work with
Signs Your Honeywell Vent Sanitizing Is Failing
- The lamp isn’t glowing. Most Honeywell housings have a small viewport near the duct. If it’s dark, the lamp has either burned out or the ballast isn’t sending power. UV lamps lose output gradually over 9,000 to 12,000 hours of runtime, which in Orlando’s near-year-round cooling season means replacement every 18 to 24 months for many homes.
- The unit is buzzing or humming louder than usual. A failing ballast often makes an audible hum before it gives out entirely. If you hear a new electrical buzz near the air handler, it’s worth checking before the part dies mid-summer.
- Allergy symptoms return despite a fresh filter. The whole point of the Honeywell sanitizing system is to knock down microbial growth on the coil and in the duct. When the lamp weakens, that protection fades, and often the first sign isn’t visual, it’s sneezing.
- Visible mold or mildew on the coil. If you can see dark spotting on the evaporator coil through the access panel, the sanitizing light isn’t doing its job. In Orlando’s humidity, a dead lamp means microbial growth returns faster than you’d think.
- The unit trips a breaker or won’t power on at all. This points to a short in the ballast or wiring. Don’t keep resetting it. A short that’s ignored can damage the housing itself, and that becomes a pricier replacement.
Replacement Cost & What’s Included
In Orlando, a Honeywell vent sanitizing lamp replacement alone typically runs $185 to $290 installed. A full ballast-and-lamp replacement lands between $385 and $720, depending on whether you have the UV100A, UV2400, or a dual-lamp configuration. The range accounts for the part itself, the hour or so of labor, and whether your air handler is in a garage closet or a tight attic space that takes longer to access safely.
Every quote we give includes the part, the labor, and cleanup, in writing, before we touch anything. You’ll see the full number before we start, and that’s the number you’ll see on the invoice. No per-vent catch, no surprise add-ons. Our work on this part is backed by our 365-Day Done Right Promise: if the replacement isn’t done right, we make it right, full stop. And like every Morton’s visit, our techs arrive in uniform, wear shoe covers, lay drop cloths where they’re working, and take a photo of the cleanup before they leave.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
What you can safely do: check the viewport to see if the lamp is glowing, note the model number on the housing label, and measure the lamp if it’s already out and you’re curious. What you should not do: attempt to replace the lamp yourself while the system has power connected. Honeywell UV systems run on line voltage, and UV light at sanitizing intensity is harmful to your eyes and skin. The housing should always be de-energized at the breaker before the lamp is handled, and the lamp itself should never be touched with bare fingers because skin oils create hot spots that shorten lamp life. If any of that sounds like more than you want to take on, that’s not a shortcoming, it’s good judgment.
We handle this repair regularly across Orlando, including older homes near College Park where tight air handler closets make the job more frustrating than the YouTube videos suggest. If you’d rather have it done right the first time, call Paul and the team at (321) 204-8194 and we’ll get you a written price before we start.
FAQs
In Orlando’s climate, where air conditioning runs most of the year, a Honeywell UV lamp typically lasts 12 to 18 months of continuous runtime before its output drops enough to matter. Honeywell rates the lamps for roughly 9,000 to 12,000 hours, but our experience in this market is that Florida humidity and long cooling seasons push most Orlando homeowners toward replacement every 18 months or so. If you’d like us to check yours, call (321) 204-8194 and we’ll take a look.
Most failures are repairable with a new lamp or ballast, and we stock both on the truck for the common Honeywell models. The housing itself rarely fails unless it’s been exposed to water or suffered an electrical short. We’ll test the unit before quoting anything, and you’ll get a written price for exactly what’s needed, not a blanket recommendation to replace everything.
A straightforward Honeywell lamp or ballast swap takes about 45 minutes to an hour once we’re at the air handler. If the unit is in a tight attic or the wiring needs attention, it can run a bit longer. We’ll tell you the time estimate along with the price before we start.
We stock the most common Honeywell UV lamps and ballasts on our trucks, including parts for the UV100A and UV2400 series. For less common or dual-lamp configurations, we can usually source the part within a day or two from our Orlando suppliers. If you’re not sure what you have, give us the model number from the housing label and we’ll check stock before we schedule your visit.
Call Morton’s Air Duct Orlando for Honeywell Vent Sanitizing
If your Honeywell vent sanitizing system is dark, buzzing, or just not doing its job anymore, call (321) 204-8194. We’ll schedule a time that works for your family, arrive in uniform with shoe covers and drop cloths, and hand you a written price before any work begins. Paul Adeyemi and our Orlando crews have been keeping duct systems clean and sanitizing units running across this city for years, and we’ll treat your home the way we’d want ours treated: no mess, no surprises, no pressure. Whether you’re near College Park, Baldwin Park, or anywhere else in the Orlando area, the fix starts with one call.
Written by Paul Adeyemi, Owner, Mortons Air Duct Orlando at Mortons Air Duct Orlando, serving Orlando and nearby areas.